DESCRIPCIÓN

Dual 18A or Single 36A DC/DC µModule Regulator

The LTM®4630 is a dual 18A or single 36A output switching mode step-down DC/DC µModule® (micromodule) regulator. Included in the package are the switching controllers, power FETs, inductors, and all supporting components. Operating from an input voltage range of 4.5V to 15V, the LTM4630 supports two outputs each with an output voltage range of 0.6V to 1.8V, each set by a single external resistor. Its high efficiency design delivers up to 18A continuous current for each output. Only a few input and output capacitors are needed. The LTM4630 is pin compatible with the LTM4620 and LTM4620A (dual 13A, single 26A) and the LTM4628 (dual 8A, single 16A).

The device supports frequency synchronization, multiphase operation, Burst Mode operation and output voltage tracking for supply rail sequencing and has an onboard temperature diode for device temperature monitoring. High switching frequency and a current mode architecture enable a very fast transient response to line and load changes without sacrificing stability. Fault protection features include overvoltage and overcurrent protection. The LTM4630IV#PBF is offered in 16mm × 16mm × 4.41mm LGA packages. The LTM4630 is ROHS compliant.

The LTM4630 has dual integrated constant-frequency current mode regulators and built-in power MOSFET devices with fast switching speed. The typical switching frequency is 500kHz. For switching-noise sensitive applications, it can be externally synchronized from 400kHz to 780kHz. A resistor can be used to program a free run frequency on the FSET pin.With current mode control and internal feedback loop compensation, the LTM4630 module has sufficient stability margins and good transient performance with a wide range of output capacitors, even with all ceramic output capacitors.

Current mode control provides cycle-by-cycle fast current limit and foldback current limit in an overcurrent condition. Internal overvoltage and undervoltage comparators pull the open-drain PGOOD outputs low if the output feedback voltage exits a ±10% window around the regulation point. As the output voltage exceeds 10% above regulation, the bottom MOSFET will turn on to clamp the output voltage. The top MOSFET will be turned off. This overvoltage protect is feedback voltage referred.

 

CARACTERÍSTICAS

Salida doble de 18 A o única de 36 A

Amplio rango de tensión de entrada: 4,5 V a 15 V

Rango de tensión de salida: 0,6 V a 1,8 V

±1.5% Maximum Total DC Output Error Over Line, Load and Temperature

Differential Remote Sense Amplifier

Control en modo corriente/Respuesta rápida a transitorios

Adjustable Switching Frequency

Protección contra sobreintensidad

Multiphase Parallel Current Sharing with Multiple LTM4630s Up to 144A

Sincronización de frecuencias

Monitor de temperatura interna

Pin Compatible con el LTM4620 y LTM4620A (Dual 13A, Single 26A) y LTM4628 (Dual 8A, Single 16A)

Funcionamiento en modo ráfaga® seleccionable

Arranque suave/seguimiento de tensión

Protección contra sobretensión de salida

16mm × 16mm × 4.41mm LGA Packages

TJMAX = 125°C, ΘJA = 7°C/W, ΘJCbottom = 1.5°C/W, ΘJCtop = 3.7°C/W, ΘJB + ΘJBA ≅ 7°C/W Θ VALUES DEFINED PER JESD 51-12

WEIGHT = 3.2g

 

APLICACIONES

Equipos de telecomunicaciones y redes

Almacenamiento y tarjetas ATCA

Equipamiento industrial

 

ELECTRICAL CHARACTERISTICS NOTE

Nota 1: Las tensiones superiores a las indicadas en los valores nominales máximos absolutos pueden provocar daños permanentes en el dispositivo. La exposición a cualquier condición de máxima tensión absoluta durante periodos prolongados puede afectar a la fiabilidad y la vida útil del dispositivo.

Nota 2: El LTM4630 se prueba en condiciones de carga pulsada tales que TJ ≈ TA. Se garantiza que el LTM4630E cumple las especificaciones de 0°C a 125°C de temperatura interna. Las especificaciones en el rango de temperatura de funcionamiento interno de -40°C a 125°C se garantizan mediante el diseño, la caracterización y la correlación con controles de proceso estadísticos. El LTM4630I está garantizado en todo el rango de temperatura de funcionamiento interno de -40°C a 125°C. Tenga en cuenta que la temperatura ambiente máxima coherente con estas especificaciones viene determinada por las condiciones de funcionamiento específicas junto con la disposición de la placa, la impedancia térmica nominal del encapsulado y otros factores ambientales.

Nota 3: Se prueban dos salidas por separado y se aplica la misma condición de prueba a cada salida.

Nota 4: La frecuencia de conmutación es programable de 400kHz a 750kHz.

Note 5: LTM4630 device is designed to operate from 400kHz to 750kHz

Nota 6: Estos parámetros se comprueban en la clasificación de obleas.

Nota 7: Véanse las curvas de reducción de corriente de salida para diferentes VIN, VOUT y TA.