ОПИСАНИЕ

The LTC2262-14 is a sampling 14-bit A/D converter designed for digitizing high frequency, wide dynamic range signals. The LTC2262-14 is perfect for demanding communications applications with AC performance that includes 72.8dB SNR and 88dB spurious free dynamic range (SFDR). Ultralow jitter of 0.17psRMS allows undersampling of IF frequencies with excellent noise performance. DC specs include ±1LSB INL (typical), ±0.3LSB DNL (typical) and no missing codes over temperature. The transition noise is a low 1.2LSBRMS. The digital outputs can be either full rate CMOS, double data rate CMOS, or double data rate LVDS. A separate output power supply allows the CMOS output swing to range from 1.2V to 1.8V. The ENC+ and ENC– inputs may be driven differentially or single ended with a sine wave, PECL, LVDS, TTL or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles.

 

ОСОБЕННОСТИ

72.8dB SNR

88 дБ SFDR

Low Power: 149mW

Одно питание 1,8 В

CMOS, DDR CMOS or DDR LVDS Outputs

Selectable Input Ranges: 1VP-P to 2VP-P

800MHz Full-Power Bandwidth S/H

Optional Data Output Randomizer

Optional Clock Duty Cycle Stabilizer

Режимы выключения и сна

Последовательный порт SPI для конфигурирования

Совместимость с 14- и 12-разрядными версиями

40-контактный (6 мм × 6 мм) корпус QFN

ПРИЛОЖЕНИЯ

 

ОПИСАНИЕ

14-Bit, 150Msps Ultralow Power 1.8V ADC

Коммуникации

Базовые станции сотовой связи

Программно-определяемые радиостанции

Портативная медицинская визуализация

Multi-Channel Data Acquisition

Неразрушающий контроль

 

ИНФОРМАЦИЯ О ПРИЛОЖЕНИЯХ

РАБОТА ПРЕОБРАЗОВАТЕЛЯ

The LTC2262-14 is a low power 14-bit 150Msps A/D converter that is powered by a single 1.8V supply. The analog inputs should be driven differentially. The encode input can be driven differentially, or single ended for lower power consumption. The digital outputs can be CMOS, double data rate CMOS (to halve the number of output lines), or double data rate LVDS (toreduce digital noise in the system.) Many additional features can be chosen by programming the mode control registers through a serial SPI port. See the Serial Programming Mode section.

АНАЛОГОВЫЙ ВХОД

The analog input is a differential CMOS sample-and-hold circuit. The inputs should be driven differentially around a common mode voltage set by the VCM output pin, which is nominally VDD/2. For the 2V input range, the inputs should swing from VCM – 0.5V to VCM + 0.5V. There

should be 180° phase difference between the inputs.

ВХОДНЫЕ ПРИВОДНЫЕ ЦЕПИ

Входная фильтрация

Если возможно, прямо на аналоговых входах должен быть установлен RC-фильтр нижних частот. Этот фильтр низких частот изолирует схему преобразователя от переключения выборки и удержания АЦП, а также ограничивает широкополосный шум от схемы преобразователя. Значения RC-компонентов следует выбирать в зависимости от входной частоты приложения.

Transformer Coupled Circuits

The center tap is biased with VCM, setting the A/D input at its optimal DC level. At higher input frequencies a transmission line balun transformer (Figures 4 to 6) has better balance, resulting in lower A/D distortion.

Encode Input

The signal quality of the encode inputs strongly affects the A/D noise performance. The encode inputs should be treated as analog signals—do not route them next to digital traces on the circuit board. There are two modes of operation for the encode inputs: the differential encode mode  and the single-ended encode mode The differential encode mode is recommended for sinusoidal, PECL or LVDS encode inputs. The encode inputs are internally biased to 1.2V through 10k equivalent resistance. The encode inputs can be taken above VDD (up to 3.6V), and the common mode range is from 1.1V to 1.6V. In the differential encode mode, ENC– should stay at least 200mV above ground to avoid falsely triggering the single-ended encode mode. For good jitter performance ENC+ and ENC– should have fast rise and fall times.